Shanghai Huitian New Material Co., Ltd
Shanghai Huitian New Material Co., Ltd Bond today and future ,with our technology!
Add to Cart
Huitian® 7243 is a one-component thread-locking anaerobic adhesive that features thixotropy, oil tolerance, fast curing, medium strength, easily disassembled, and resistance against the fluid. The product cures when confined in the absence of air between close-fitting metal surfaces.
Typical Application
Locking and sealing of threaded fasteners to prevent thread corrosion, particularly suitable for locking and sealing lightly oiled bolt surfaces. Surface locking and sealing of bolts on inert surfaces (stainless steel, aluminum, gold-plated, etc.) or bolts with high-temperature resistance (up to 180°C) requirements.
Middle Strength Blue Thixotropic Anaerobic Thread Locker 7243 replacing Loctite 243
Properties before curing
Typical value Range
Appearance Blue liquid
Chemical type Methacrylate
Viscosity (mPa·s)
(GB/T2794-1995)
Brookfield RVT
3# spindle 20 rpm 1,600-1,900 thixotropy
2.5rpm 6,000-10,000 thixotropy
Density (g/cm3) 1.08 1.00-1.15
(GB/T13354-1992)
Flash point (℃) ＞93
(SH/T0733-2004)
Max filling gaps (mm) 0.13
Fixture time (min) ≤20
Properties after curing
Curing time at RT (h) 24
Breakaway torque (N·m) 20 7.9-22.6
(GB/T18747.1-2002)
Average dismounting torque (N·m) 10 2.3-16.9
(GB/T18747.1-2002)
Working temperature (℃) -50-180
Chemical/solvent resistance
Aged under conditions indicated and tested @ 22°C
Solvent Temperature (℃) % of initial strength
100h 500h 1000h 5000h
Engine oil 125 100 100 95 95
Leaded petrol 22 100 100 96 96
Brake fluid 22 100 100 100 100
Ethanol 22 100 90 90 85
Ace-tone 22 100 100 90 90
Water/glycol 87 95 90 85 85
(50%/50%)
Directions for use
Clean-up: For best results, clean all surfaces (external and internal) with a Huitian 7755 cleaning solvent and allow to dry.
Gluing: Apply glue evenly to the thread engagement area, with sufficient glue to fill the thread gap, and tighten in one pass as required by the specification. Curing speed slows down as the gap increases If the cure speed is too slow, spray all threads with Activator 7769 and allow to dry.
Assembly: Shake the product thoroughly before use. To ensure that the system achieves maximum performance, the recommended curing time is 24 hours or more to ensure that the adhesive layer is fully cured.
Cautions
Not suitable for use on plastic parts, not suitable for use in pure oxygen and oxygen-rich systems, and not for sealing chlorine or other strong oxidizing substances.
Store unused glue in a sealed container for next use. Contaminated glue should not be refilled into the original bottle as this may affect the performance of the remaining glue.
This product contains acrylic and methacrylate substances which are irritating to the skin and eyes. Recommended for use in a ventilated area. In case of accidental contact with eyes and skin, rinse immediately with water.
Keep away from children for storage.
For safe handling information on this product, consult the Safety Data Sheet (SDS).
Packing specification
Order code: 724301,50ml/, 10 pcs/carton, 80 pcs/box
724303, 250ml/bottle, 10 pcs/carton
Storage
Optimal Storage: 8 °C to 21 °C. Storage below 8 °C or greater than 28 °C can adversely affect product properties.
Shelf life is 18 months
We can also make:
1.Low strength & thixotropic thread locker
2.Middle strength & thixotropic thread locker
3.High strength & oil resistant thread locker
4.High strength & chemical resistant thread locker
5.High strength & thixotropic thread locker
6.High strength & high viscosity thread locker
7.High strength & middle viscosity thread locker
8.High strength & high-temperature resistant thread locker
9.High strength & fast osmotic thread locker
Our Advantages:
1. Listed company in China (stock code: 300041)
2. Famous Trademark of China
3. Fast Delivery
4. OEM services/small orders are welcome